Color Change Corporation
Material Safety Data Sheet #2500
Effective Date: July 1, 2002
______________________________________________________________________________
Color Change Corporation urges each customer or recipient of this MSDS to study it carefully to become aware of and understand the hazards associated with the product. The reader should consider consulting reference works or individuals who are experts in ventilation, toxicology, and fire prevention, as necessary or appropriate to use and understand the data contained in this MSDS.
To promote safe handling, each customer or recipient should: (1) notify its employees, agents, contractors and others whom it knows or believes will use this material or the information in this MSDS and any other information regarding hazards or safety; employees, customers, and other users of the product of this information.
Color Change Corporation
1545 Burgundy Parkway
Streamwood, IL 60107-1811
Tel: (630) 289-0900
Fax: (630) 289-0909
Emergency Response: (800) 424-9300
______________________________________________________________________________
I. Material Identification
Product Name/Numbers: Thermochromic Epoxy Resin Ink, LD-X
Chemical Name: EPOXY RESIN INK, THERMOCHROMIC
Chemical Family:
Formula:
Molecular Weight:
Synonyms:
CAS # and Name:
Manufacturers: Color Change Corporation
_____________________________________________________________________
Precautionary Labeling
National Paint and Coatings Association Hazardous Material Identification System
_____________________________________________________________________
II. Physical Data
Boiling Point: > 300°F
Specific Gravity (H20 = 1): average 1.05
Freezing Point: N/A
Vapor Pressure at 20°C: UNK
Evaporation Rate: N/A
Solubility in Water by wt: immiscible
Appearance: colored paste
Odor: no characteristic odor
Physical State: liquid
Percent Volatiles (by volume): 40-45%*
* Tested according to EPA test method 24. The specific VOC number for each product covered by this MSDS may be obtained by contacting Color Change Corporation.
______________________________________________________________________________
III. Ingredients
% Material CAS# Exposure Limit
Trade Secret
______________________________________________________________________________
IV. Fire and Explosion Hazard Data
Flash Point (test method(s)): 150°F (SETA Flash)
Flammable Limits in Air (% by volume): LOWER: 1%
UPPER: N/A
Special Fire Fighting Procedures: Use self-contained breathing apparatus and protective clothing. Water may be ineffective but may be used to cool containers. Fumes released may be toxic and dangerous.
Extinguishing Media: Use water spray, foam, carbon dioxide, dry chemical media.
Unusual Fire and Explosion Hazards: None
______________________________________________________________________________
V. Health Hazard Data
Exposure Limit(s) 2-butoxyethanol: ethylene glycol monobutyl ether CAS# 111-76-2 (15-22% by weight) 20 ppm ACGIH - TLV, 25 ppm OSHA - PEL
Napthalene: petroleum distillate CAS# 91-20-3 (<3% by weight) 10 ppm ACGHI – TLV, 10ppm OSHA – PEL
Dipropylene glycol methyl ether: Aliphatic glycol ether CAS# 34590-94-8 (5-13% by weight) 100 ppm ACGIH – TLV, 100 ppm OSHA - PEL
Effects of Single Overexposure:
Swallowing: May cause abdominal discomfort, nausea, vomiting, and diarrhea. Contains material that may be moderately toxic if ingested.
Skin Absorption: Penetrates the skin readily. Toxic and may be harmful if absorbed through the
skin. May cause irritation, defatting or dermatitis.
Inhalation: Repeated and prolonged overexposure by inhalation may cause respiratory tract irritation. Symptoms may include nervous system disorders such as headaches, dizziness, weakness and fatigue.
Skin Contact Skin contact may cause irritation. Prolonged or repeated contact may cause discomfort and local redness. Penetrates the skin readily. Toxic and may be harmful if absorbed through the skin.
Eye Contact: Causes severe irritation, experienced as discomfort or pain, excess blinking and tear production, marked excess redness and swelling of the conjunctiva, and chemical burns of the cornea. Iritis may occur.
Medical Conditions Aggravated by Overexposure:
Pregnant women and persons with pre-0existing health disorders should consult their physician before using this product. Repeated and prolonged overexposure and/or individual sensitivity may increase the potential for and degree of adverse health effects.
Significant Laboratory Data with Possible Relevance to Human Health Hazard Evaluation:
2-Butoxyethanol has caused reproductive and blood disorders resulting in kidney, liver and lung damage in lab animals.
Dipropylene glycol methyl ether has been suggested to cause the following effects after overexposure and in lab animals,
and may aggravate pre-existing disorders of these organs in humans: mild, reversible liver and kidney effects. For animal
studies, reference TSCA Section 4 Test Rule Results or contact the manufacturer for further details.
Emergency and First Aid Procedures:
Swallowing: If victim is conscious, DO NOT induce vomiting. Never give liquids to an unconscious person. Get medical attention immediately.
Skin: Remove contaminated clothing. Remove excess with absorbent material. Wash skin with soap and water for at least 15 minutes. Cool water is usually recommended to prevent the pores of the skin from opening. Obtain medical attention if irritation persists. Wash or discard clothing before reuse.
Inhalation: If any symptoms develop, remove to fresh air. If necessary, give artificial respiration. Get medical attention.
Eyes: Immediately flush eyes with water and continue washing for at least 15 minutes. Obtain medical attention without delay, preferably from an ophthalmologist.
______________________________________________________________________________
VI. Reactivity Data
Stability: Material is stable
Conditions to Avoid: Prolonged excessive heat may cause product decomposition, ignition sources,
sparks, and open flame.
Incompatibility (materials to avoid): Strong oxidizing agents
Hazardous Combustion or Decomposition Products: Burning can produce the following combustion products:
carbon monoxide, carbon dioxide, and other noxious gases.
Hazardous Polymerization: Not anticipated during normal storage and usage conditions.
______________________________________________________________________________
VII. Spill, Leak and Disposal Procedures
Steps to be taken if material is released or spilled:
Wear eye and skin protection. Floor may be slippery; use care to avoid falling. Contain spills immediately with inert materials (e.g. sand, earth). Avoid discharge to natural waters. Transfer liquids and solid diking material to suitable containers for recovery or disposal. Use absorbent to clean remainder.
Waste Disposal Method: Small amounts can be hardened with absorbent material and disposed of as a solid. Dispose of all materials in accordance with the applicable local, state, and federal regulations.
_____________________________________________________________________________
VIII. Special Protection Information
Respiratory Protection (specify type): Wear a MSHA/NIOSH approved (or equivalent) half-mask air purifying respirator.
Ventilation: Local exhaust as needed by operators near processing equipment.
Protective Gloves: Impervious (Neoprene)
Eye Protection: Monogoggles recommended
Other Protective Equipment: Eye Bath, Safety Shower, Chemical Apron
IX. Special Precautions
Precautions to be taken in handling and Storage:
Do not store near heat or flame, material can gel with long exposure to elevated temperatures (above 90° F).
DANGER!
· Causes eye burns.
· Harmful if swallowed.
· Causes skin irritation.
· Do not get in eyes.
· Do not swallow.
· Avoid contact with skin and clothing.
· Keep container closed.
· Use with adequate ventilation.
· Wash thoroughly after handling.
NOT INTENDED FOR DRUG USE
FOR INDUSTRY USE ONLY
______________________________________________________________________________
NOTE---
All recommendations and statements made, if any, are based on Color Change Corporation's research and experience. However, since Color Change Corporation has no control over the conditions of use or storage of the product sold, Color Change Corporation cannot guarantee the results obtained through the use of its products. All products are sold and samples given without any representation or warranty, expressed or implied, of fitness for any particular purpose or otherwise, and upon condition that the buyer shall determine the suitability of the product for its own purposes. This applies also where protective rights of third parties are involved. It does not release the user from the obligation to test the suitability of the product for the intended use and application. Color Change Corporation makes no warranty as to the absolute correctness or sufficiency of any of the foregoing or that additional or other measures may not be required under particular conditions.